A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
The article in the next paragraphs on the subject of How to Install a Bathtub is amazingly stimulating. Don't miss it.
Mounting a bath tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately tough task. If the old bathtub is easily easily accessible, the job can relocate easily; if you need to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the new one. Ensure you have qualified yourself for the work as well as are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This short article will certainly aid you install a new tub in your restroom if you have actually currently gotten a new tub and also do not need to change the setup of your previous water system pipes.
Your devices as well as material list should consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic due to the limited accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Safeguard the tap in position with the manufacturer provided backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous type needs to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are practical in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to guarantee that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipe by making a compression join; then do the same for the various other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the producer's user's manual. Tiling as well as securing around the tub needs to wait up until the bathtub has actually been made use of a minimum of when as this will certainly settle it right into its last position.
Getting ready for the Setup
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile tap adapters to the bottom of both faucets using 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall surface between the bath as well as the tiling, resulting in difficulties with moisture and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components as well as installations. They are marketed in tubes as well as cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the tub with water before securing, to allow for the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader on A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that post was a good thing. Are you aware of another person who is curious about the topic? Why not share it. Thank-you for taking the time to read it.
Book Appointment Now Report this page